Tippet Setting Of Tata Cummins 4BT Engine Single Single Cyl.

Tippet Setting Of Tata Cummins 4BT Engine Single Single Cyl.

TATA CUMMINS 4BT ENGINE TIPPET SETTINGS

Tippet Setting of Tata Cummins 4bt Engine Hello Friends I am Ravi Kharkhate going to tell and today through a blog post how to Tippet Setting of Tata Cummins 4bt Engine step by step adjusting wall of single single cylinder,

TIPPET SETTING METHOD 
To Tippet Setting of Tata Cummins 4bt Engine, first of all we have to open the Tippet cuver of all four cylinders, after that we will need three spinners (1) Tippet Gagde (2) Screwdriver (3) Ring Spanner of 14-15 We will set the engine type in 4 times. To set the single cylinder and the Inlet wall is 0.25mm and the Exhaust wall 0.45mm. To Tippet Setting, we have to use a screw lock nut to loosen that lock nut and Tippet gajde. According to the setting of the screw, after setting, the locking screw is to be locked. To make the Tippet Setting, we have to turn the engine to turn on the timing and 4 Setting Tippet,
TIPPET SETTING FIRST STEP
TIPPET SETTING SECOND STEP
TIPPET SETTING THIRD STEP
TIPPET SETTING FOURTH STEP

TIPPET SETTING FIRST STEP, 
To Tippet Setting of first number cylinder, the first thing we need to do is to rotate the engine and bring one number and four number cylinders into the top. To check whether the piston came into the top, check the rotor of one or four number cylinders with a screwdriver. Have to either open the plunger plate of the pump and bring first number of the pump to the top of the plunger, after which one has to set the type of both the rowers of the cylinder Inlet wall 0.25 mm And  Adjust Wall 0.45 mm is set in the inlet wall 10 Thaw and Adjust Wall 18 Thaw Tippet Setting,

TIPPET SETTING SECOND STEP,
To Tippet Setting of the three number cylinder, we have to rotate the engine to bring the two or three number pistons to the top. The first step to check the piston at the top is stated in the same way, but the top number of the piston is now The top number is to be followed by the Tippet Setting of both rocker of three number cylinders in the same way as mentioned in the first step,

TIPPET SETTING THIRD STEP,
To Tippet Setting of the four number cylinder, we have to rotate the engine again and bring the piston of one or four number cylinders to the top. The first step to check the piston at the top is to be checked in the same way, but the pump plunger The number four has to be brought to the piston top, then the Tippet Setting of both the rocker number four is to be done the same way as mentioned in the first step,

TIPPET SETTING FOURTH STEP,
To Tippet Setting of the two number cylinder, we have to rotate the engine and bring the piston of the number three cylinder to the top, to check the piston at the top, first step is given but the number of the pump plane is to bring the piston to the top After that the Tippet Setting of both the two number rankers is the same as that mentioned in the first step,

So guys you can Tippet Setting by doing a single single cylinder of Tata Cummins 4BT Engine in this way,

For More information you can visit our YouTube channel MECHANIC GYAAN

Friends, how did you like This information, write in the comment, if you like it, like it and share it with friends, follow us to read other similar posts, what will happen, friends, whenever I upload a post, then throw the notification Will find it
                                                  Thank you,

My Youtube Channel

My Facebook Page

My Website

Leave a Reply

Your email address will not be published. Required fields are marked *

error: Content is protected !!